Key Features

• NXP S32K344EHT1VPBST chipset
• Wide input voltage range: 6V to 17V
• Input power monitoring via INA219
• USB Type-C for power supply
• Switchable voltage for VDD_HV_A bus (3.3V or 5V)
• Onboard Segger J-Link debugger
• Onboard USB to UART converter (CP2102)
• Three CAN FD transceivers
• One 100Base-T1 Ethernet transceiver
• Two LIN transceivers
• 64Mb QSPI flash memory
• Two user-programmable switches
• Two RGB LEDs
• 16 MHz high-speed external oscillator (HSE) and 32.768 kHz low-speed external oscillator (LSE)
• High-precision (3.3V ± 0.2%) voltage reference for ADC

Specifications & Features of DS3231 Real Time Clock (RTC) Module:-

1. Two Time-of-Day Alarms.
2. Digital Temp Sensor Output.
3. Register for Aging Trim.
4. DS 3231 RTC with 2032 Battery Holder.
5. Highly Accurate RTC Completely Manages All Timekeeping Functions.
6. Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year, with Leap-Year Compensation Valid Up to 2100.
7. Configurable I2C device Address for AT24C32 using SMD jumpers on PCB (A0, A1, A2).
8. Programmable Square-Wave Output Signal.
9. Battery-Backup Input for Continuous Timekeeping.
10. Low Power Operation Extends Battery-Backup Run Time.

Specifications & Features of MAX7219 LED Dot Matrix 4 In 1 Display with 5P Line Module:-

• Dimensions: 128 x 32  x 1.5mm(LxWxH)(All 4 in 1)
• Dimension 32 x 32 x 1.5 mm (LxWxH) (Single Module)
• A single module can drive an 8×8 dot matrix common cathode
• Operating voltage: 5V
• Weight: 55 gm
• Fixing screws with 64 holes with a diameter 3mm
• Module with input and output interfaces
• Support for cascading multiple modules

Specifications & Features of MAX7219 dot matrix module microcontroller module DIY KIT:-

1. Requires only 3 communication wires of MCU
2. Cascading multiple Matrix LED Module is very easy
3. Size of the display is very compact
4. The PCB features M3 holes for mounting.

Specifications & Features of MAX30100 Pulse Oximeter Heart Rate Sensor Module:-

Specifications & Features of BMP180 Digital Barometric Sensor Module compatible:-

Specifications & Features of NEO-6M GPS Module with EPROM:-

• 5Hz position update rate
• Operating temperature range: -40 TO 85°CUART TTL socket
• EEPROM to save configuration settings
• Rechargeable battery for Backup
• The cold start time of 38 s and Hot start time of 1 s
• Supply voltage: 3.3 V
• Configurable from 4800 Baud to 115200 Baud rates. (default 9600)
• SuperSense ® Indoor GPS: -162 dBm tracking sensitivity
• Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
• Separated 18X18mm GPS antenna

Specifications & Features of SIM900A Wireless GSM GPRS Module with Antenna:-

• Quad-Band GSM/ 850/900/1800/1900MHz
• Compatible with arduino, raspberry pi, arm, avr, pic, 8051
• power supply 12v 1amp to 2 amps max
• Use in the area of full signal strength.
• Perfect suited for GSM based Microcontroller Projects (better than SIM300 and other GSM Modems)
• Option for connecting MIC and SPEAKER directly to GSM MODEM for calls (LINE IN also available)
• Supports communication through RS232 with DB9 Connector, TTL Pins and I2C Pins
• CALL SMS GPRS facility - MIC input, LINE input and SPEAKER output pins

Specifications & Features of SIM800L GPRS GSM Module Micro SIM Card Core Board Quad-band TTL Serial Port:-

• Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested).
• Make and receive voice calls using a headset or an external 8Ω speaker and electret microphone.
• PWM/Buzzer vibration motor control
• AT command interface with "auto baud" detection
• Send and receive SMS messages.
• Send and receive GPRS data (TCP/IP, HTTP, etc.).
• Scan and receive FM radio broadcasts.
• Lead out buzzer and vibration motor control port.
• AT command interface with "auto baud" detection.
• Onboard IPEX socket that can be connected to external antenna.

LDR sensor module is used to detect the intensity of light. […]