ProBug V2 isolated is a fully galvanically isolated programmer and […]

Cost effective. easy to use breadboard compatible automotive development board based on the NXP S32K144 microcontroller having ISO26262 ASIL Class B. Onboard Segger J-Link for programming and debugging. No need for external debugger. Integrated the Bosch BNO055 IMU sensor and CAN Transceiver. USB to UART also available on board through onboard Segger J-Link debugger with USB Type-C.

Specification of STM32 ECU: -

• Power Electronics.
• Environmental Monitoring.
• Home Automation.
• Embedded Systems Development.
• IoT (Internet of Things) Prototyping.

Specifications & Features of JLink V9 Debugger Emulator: -

• Type C cable Powered and connection to Host Desktop/Laptop
• Works on SWD protocol for programming and debugging the NXP S32K1xx and NXP S32K3xx Series of MCU's.
• Configured as Jlink Debugger for Programming/Debugging via S32 Design Studio/FreeMaster/ MBDT/Jlink Software Toolchain
• 2 Debug Connectors to connect to Host NXP Semiconductors S32K Microcontroller's: 20 Pin JTAG and 10 Pin SWD connector
• Power configurable to Host NXP S32K MCU between 3.3 V and 5V.
• Can provide 3.3V or 5V and uptp 1A current for the development board by powering the S32K MCU via ProBug Debugger.
• Onboard Reset Button to reset the Host NXP S32K MCU via Debugger and also Power/Communication LEDs.
• Virtual UART COM Port Detection via same Debug connector for logging Realtime data via UART Peripheral.

--------------------------------------------------------------- Technical Specifications and Features of Innomaker: - ---------------------------------------------------------------

• Compatibility: Raspberry Pi Zero(W)/Pi3B+/PI4/Beagle bone/Tinker Board and any single-board computer.
• Power: USB-powered, no external power required.
• CAN Baud Rate: Supports a broader range of CAN baud rates, from 20Kbps to 1Mbps and both CAN bus 2.0A and 2.0B specifications, ensuring compatibility with a wide range of CAN-enabled devices.
• Microcontroller: Onboard STM32F0 microcontroller with DMA technique.
• Protection: Power supply isolation, signal input/output isolation, surge/static protection, selectable 120-ohm resistor.
• Software Support: C/Python demos of Socket-CAN, InnoMaker Windows/MacOs/Linux Soft_API.
• Certifications: CE and FCC certified.

Key Features

• NXP S32K344EHT1VPBST chipset
• Wide input voltage range: 6V to 17V
• Input power monitoring via INA219
• USB Type-C for power supply
• Switchable voltage for VDD_HV_A bus (3.3V or 5V)
• Onboard Segger J-Link debugger
• Onboard USB to UART converter (CP2102)
• Three CAN FD transceivers
• One 100Base-T1 Ethernet transceiver
• Two LIN transceivers
• 64Mb QSPI flash memory
• Two user-programmable switches
• Two RGB LEDs
• 16 MHz high-speed external oscillator (HSE) and 32.768 kHz low-speed external oscillator (LSE)
• High-precision (3.3V ± 0.2%) voltage reference for ADC

Specifications & Features of JLink V9 Debugger Emulator: -

• The main control chip adopts STM32F205, not lose firmware, and the hardware is upgraded to the latest version of V9.4
• Can provide 3.3V and 0.8A current for the development board (pin 2)
• Support standard JTAG interface and 2-wire SWD debugging interface. The speed can reach 20M (JTAG) / 15M (SWD) per second.
• Support debugging of all ARM chips, support MDK or IAR, and compile environment IDE supported by other standard JLink.
• Original firmware, full automatic upgrade The main control chip adopts STM32F205, without losing the firmware, and the hardware is upgraded to the latest version of V9.4

Specification & Features of USB Logic Analyze: -

1. Logical light indication: a small light indicates CHO electrical level.
2. Input feature: 5PF,100K Ohm.
3. USB power supply; USB logic analyzer for monitoring, analyzing and debugging digital circuits.
4. 8-Channels USB logic analyzer with a 24Mhz sampling frequency
5. Can analyze UART, IIC, and SPI, etc. automatically.
6. Great for MCU, ARM system and FPGA development
7. Voltage: 0-5.5V

• S32K144 MCU in LFQP100 pin package.
• onboard RGB LED and 2 switches
• 1 Variable Potentiometer
• On-board UART for debugging via Type C USB cable
• On-Board CAN transceiver IC TJA1051 via green screw Terminals.
• TX-RX LED indicator pins for onboard UART and CAN communication.
• Onboard JTAG-SWD 10-pin Connector for JLink SWD Debugging

Specifications & Features of DS3231 Real Time Clock (RTC) Module:-

1. Two Time-of-Day Alarms.
2. Digital Temp Sensor Output.
3. Register for Aging Trim.
4. DS 3231 RTC with 2032 Battery Holder.
5. Highly Accurate RTC Completely Manages All Timekeeping Functions.
6. Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year, with Leap-Year Compensation Valid Up to 2100.
7. Configurable I2C device Address for AT24C32 using SMD jumpers on PCB (A0, A1, A2).
8. Programmable Square-Wave Output Signal.
9. Battery-Backup Input for Continuous Timekeeping.
10. Low Power Operation Extends Battery-Backup Run Time.